Several problems occurring in sublimation fabric printing machine
Do you often have such or such minor faults when you use the sublimation fabric printing machine? How did you solve it then?
Below are some of my tidying points about the problems that often arise when the roller drum heat transfer machine is working. Let's take a look at them.
Drag pulp: Drag a small non-pattern with or without the same color under the pattern. The reason may be:
1. The scraper device is too high
2. The color paste is too thick to absorb the fabric in an instant and then the cylinder is brought into the pattern
3. The arrangement of the cylinder is unreasonable and so on. Generally, it can be solved by adjusting the angle of the knife, the thickness of the color paste and the knife.
Knife Jump: The transverse stripes left on the fabric due to the flicker of the knife blade, which makes the size on the cylinder not scraped clean. The primary reason may be that the scraper device is too low to form the scintillation of the blade or the lack of pressure on the heavy hammer. Of course, the inappropriate flower tube device and the loose gear occlusion can also form a jumping knife.
Knife blade: One or more color lines are formed on the surface of the fabric. First of all, the scraper has a small gap (the knife has been used for a long time, the surface of the flower tube is rough, etc.) or is sticky with impurities (velvet, insoluble matter in the color paste, etc.) so that the color paste on the flower tube is not scraped clean.
Splashing: Splashing some colours from the knife edge onto the fabric. Scraper device is too low, speed is too fast, slurry is too thin, the flower drum is the cross-grain of the simple occurrence of this defect, if the adjustment can not be solved, can be covered with a cloth above the flower drum to block. In addition, if there are sand holes in the flower tube, the color spots are formed regularly according to the circumference, which is different from splashing.
Open field: The pattern of printed fabrics shows some ground color. Reasons: low capillary effect, thick size, too fast speed, poor pressure, shallow shade, etc. If the axle core is bent, it will form color difference between left, middle and right, and even open ground. It should be replaced in time.
About the small problems often occurring in the roll drum heat press and their solutions, I'll share them with you today. If you have any questions, please leave a message below.
More info:
Website: www.skyimagepaper.com
Company Name: Fei Yue Digital Technology Co.,LTD
E-mail: janezhang940213@gmail.com
Tel: 86-025-86628894
Whatsapp: +86 18851084450
Address: Central Road 323, Nanjing, Jiangsu, China
Below are some of my tidying points about the problems that often arise when the roller drum heat transfer machine is working. Let's take a look at them.
1. The scraper device is too high
2. The color paste is too thick to absorb the fabric in an instant and then the cylinder is brought into the pattern
3. The arrangement of the cylinder is unreasonable and so on. Generally, it can be solved by adjusting the angle of the knife, the thickness of the color paste and the knife.
Knife Jump: The transverse stripes left on the fabric due to the flicker of the knife blade, which makes the size on the cylinder not scraped clean. The primary reason may be that the scraper device is too low to form the scintillation of the blade or the lack of pressure on the heavy hammer. Of course, the inappropriate flower tube device and the loose gear occlusion can also form a jumping knife.
Knife blade: One or more color lines are formed on the surface of the fabric. First of all, the scraper has a small gap (the knife has been used for a long time, the surface of the flower tube is rough, etc.) or is sticky with impurities (velvet, insoluble matter in the color paste, etc.) so that the color paste on the flower tube is not scraped clean.
Open field: The pattern of printed fabrics shows some ground color. Reasons: low capillary effect, thick size, too fast speed, poor pressure, shallow shade, etc. If the axle core is bent, it will form color difference between left, middle and right, and even open ground. It should be replaced in time.
About the small problems often occurring in the roll drum heat press and their solutions, I'll share them with you today. If you have any questions, please leave a message below.
More info:
Website: www.skyimagepaper.com
Company Name: Fei Yue Digital Technology Co.,LTD
E-mail: janezhang940213@gmail.com
Tel: 86-025-86628894
Whatsapp: +86 18851084450
Address: Central Road 323, Nanjing, Jiangsu, China
评论
发表评论